Panasonic PT-DS8500U Operations Instructions Page 110
- Page / 129
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Replacement
110
- ENGLISH
Maintenance
J
Lamp unit
The LAMP unit is consumable product. You can check the duration of usage time using [LAMP1/LAMP2] of
[STATUS] (
Æ
page 83) in the [PROJECTOR SETUP] menu.
Replacement of the lamp unit should be carried out by a qualied technician.
Contact the dealer to purchase a replacement lamp unit (ET-LAD310:1 bulb unit, ET-LAD310W: 2 bulb units).
J
Precautions on lamp unit replacement
Handle the lamp unit with special care as the lamp is made of glass. Dropping or giving it a shock may
z
cause it to burst or damaged.
Phillips screwdriver is necessary when replacing a lamp unit.
z
When replacing the lamp unit, be sure to hold it by the handle.
z
The lamp may burst. Replace the lamp unit carefully so that the broken pieces of the lamp glass will not
z
scatter. When the projector is mounted on the ceiling, do not work directly under the projector or put your
face closer to the projector.
For disposition of used lamps, request an industrial waste disposal contractor.
z
Attention
Do not attempt replacement with an unauthorized lamp unit.
z
The part numbers of accessories and separately sold components are subject to change without notice.
z
Wait for more than 1 hour and make sure the lamp unit and the surroundings are cooled enough.
z
Prior to replacing the lamp unit, allow it to cool down to prevent the risk of burns, damage and other hazards.
z
J
When to replace the lamp unit
When the lamp is consumed, the brightness may decrease over time. 3 000 hours of use is the replacing
time as a rough guide, and that might be shortened by the usage conditions, characteristics of the lamp
unit or environmental conditions. Therefore, it is strongly recommended for the user to keep a spare lamp.
If the lamp unit has not been replaced after 3 000 hours of operation have elapsed, the power will turn off
automatically approximately 10 minutes after it is turned on.
On screen LAMP indicator
LAMP
Over 2 800 hours
[REPLACE LAMP] is displayed on the upper left
of the screen for 30 seconds. Press any button to
clear the screen, or disappears after 30 seconds.
Lights in red.
Over 3 000 hours
[REPLACE LAMP] is displayed on the upper left
of the screen, and it will stay until you respond. To
clear the screen, press any button.
Note
The guide times,
z
3 000 hours, are rough estimates based on certain conditions and are not a guaranteed time.
REPLACE LAMP
- Operating Instructions 1
- PT-DZ8700U 1
- PT-DS8500U 1
- PT-DW8300U 1
- Important Safety Notice 2
- Heightened luminance 4
- Lengthened lamp 4
- Reduced standby power 4
- Contents 5
- Maintenance 7
- Appendix 7
- - ENGLISH 10
- Cautions when transporting 11
- Cautions when installing 12
- ENGLISH 13
- Security 14
- Cautions on use 14
- Cleaning and maintenance 15
- Disposal 15
- Accessories 16
- About Your Projector 17
- Projector body 18
- Setting projector ID number 20
- Using a wired remote control 20
- Setting up 21
- Connections 34
- How to remove the projection 37
- Powering ON/OFF 38
- Powering up the projector 39
- Making adjustment and 39
- Powering off the projector 40
- Direct power off function 40
- Projecting 41
- Using the SHUTTER function 46
- On-screen display function 46
- Switching the input signal 46
- STATUS function 46
- Automatic adjustment 47
- Using the FUNCTION button 47
- Displaying the internal 47
- Changing the picture aspect 48
- Menu Navigation 49
- MAIN MENU 50
- SUB MENU 50
- PICTURE menu 52
- CONTRAST 53
- BRIGHTNESS 53
- COLOR TEMPERATURE 54
- SYSTEM DAYLIGHT VIEW 55
- SHARPNESS 56
- NOISE REDUCTION 56
- DYNAMIC IRIS 56
- (PT-DZ8700U/PT-DS8500U only) 57
- POSITION menu 58
- (PT-DZ8700/PT-DS8500 only) 60
- (PT-DW8300 only) 62
- ADVANCED MENU 63
- INPUT RESOLUTION 64
- CLAMP POSITION 64
- EDGE BLENDING 64
- FRAME DELAY 66
- RASTER POSITION 66
- DISPLAY LANGUAGE menu 67
- DISPLAY OPTION menu 68
- (PT-DZ8700 only) 70
- AUTO SIGNAL 71
- AUTO SETUP 71
- (Only RGB input) 72
- BACK COLOR 74
- STARTUP LOGO 74
- PROJECTOR SETUP menu 75
- COOLING CONDITION 76
- LAMP SELECT 76
- LAMP RELAY 76
- LAMP POWER 77
- BRIGHTNESS CONTROL 77
- STANDBY MODE 81
- SCHEDULE 81
- NO SIGNAL SHUT-OFF 84
- REMOTE2 MODE 84
- FUNCTION BUTTON 84
- DATE AND TIME 84
- LENS CALIBRATION 85
- FILTER COUNTER RESET 85
- LOAD ALL USER DATA 86
- INITIALIZE 86
- SERVICE PASSWORD 86
- SAVE ALL USER DATA 86
- P IN P menu 87
- TEST PATTERN menu 88
- SIGNAL LIST menu 89
- Managing the sub memory 90
- SECURITY menu 91
- DISPLAY SETTING 92
- TEXT CHANGE 92
- MENU LOCK 92
- MENU LOCK PASSWORD 92
- CONTROL DEVICE SETUP 93
- Network connections 95
- NETWORK menu 100
- Monitor Lamp indicators 107
- Replacement 109
- Troubleshooting 112
- Technical Information 114
- Control commands via LAN 115
- Serial terminal 117
- REMOTE 2 IN terminal 120
- List of compatible signals 122
- Specications 124
- Dimensions 126
- About brand 126
- Attachment procedure 127
- ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ 129
Related products and manuals for Data projectors Panasonic PT-DS8500U
(74 pages)
(62 pages)© 2020, manymanuals.com. All rights reserved. | 1.405 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals